product specification date 03/26/2012 no.62p51004 cosmo electronics corporation photocoupler KPC6N139H sheet 1 of 5 rev. 2 general purpose type photocoupler z features 1. pb free and rohs compliant. 2. high current transfer ratio ( ctr min. 500% at i f =1.6ma ) 3. high speed response ( t phl typ. 0.2us at r l =270 ? ) 4. high common mode rejection voltage ( cm h typ. 500v/us ) 5. ttl compatible output 6. agency approvals ul approved ul1577 , no.e169586 cul approved c22.2 no.1 & ntc no.5 , no.e169586 vde approved en60747 , no.40006080 fimko approved en 60065 no. fi 25798 en 60950 no. fi 25798 z application 1. interfaces for computer peripherals. 2. electronic calculators, measuring instruments, control equipment. 3. telephone sets. 4. signal transmission between circuits of different potentials and impedances.
product specification date 03/26/2012 no.62p51004 cosmo electronics corporation photocoupler KPC6N139H sheet 2 of 5 rev. 2 z outside dimension unit ( mm ) e b u b ! d p e f y y y 7 o 2 4 : d p t n p tolerance 0.2mm z schematic top view 12 8 7 4 3 5 6 1. nc 2. anode 3. cathode 4. nc 5. gnd 6. v o 7. v b 8. v cc
product specification date 03/26/2012 no.62p51004 cosmo electronics corporation photocoupler KPC6N139H sheet 3 of 5 rev. 2 z absolute maximum ratings ( ta=25 ) parameter symbol rating unit forward current i f 20 ma *1 peak forward current i f 40 ma *2 peak transient forward current i fm 1 a reverse voltage v r 5 v input power dissipation p 35 mw supply voltage v cc -0.5 to 18 v output voltage v o -0.5 to 18 v emitter-base reverse with stand voltage ( pin5 to 7 ) v ebo 0.5 v *3 average output current i o 60 ma output power dissipation p o 100 mw *4 isolation voltage 1 minute v iso 5000 vrms operating temperature t opr 0 to +100 storage temperature t stg -55 to +125 *5 soldering temperature 10 second t sol 260 *1 50% duty cycle, pulse width 1ms *2 pulse width 1u Q s, 300pps *3 decreases at the rate of 0.7ma/ if the external temperature is more than 25 . *4 40 to 60% rh, ac for 1 minute *5 for 10 seconds z electro-optical characteristics ( ta=0 to +70 unless otherwise specified ) parameter symbol conditions min. typ. max. unit ctr(1) i f =0.5ma, v o =0.4v, v cc =4.5v 400 1800 - % *6 current transfer ratio ctr(2) i f =1.6ma, v o =0.4v, v cc =4.5v 500 1600 - % v ol (1) i f =6.4ma, i o =1.6ma, v cc =4.5v - 0.1 0.4 v v ol (2) i f =5ma, i o =15ma, v cc =4.5v - 0.1 0.4 v logic ( 0 ) output voltage v ol (3) i f =12ma, i o =24ma, v cc =4.5v - 0.1 0.4 v logic ( 1 ) output current i oh i f =0, v o =v cc =18v - 0.05 100 ua logic ( 0 ) supply current i ccl i f =1.6ma, v o =open, v cc =5v - 0.5 - ma logic ( 1 ) supply current i cch i f =0, v f =open, v cc =5v - 10 - na input forward voltage v f ta = 2 5 , i f =1.6ma - 1.5 1.7 v input forward voltage temperature coefficient v f / ta i f =1.6ma - -1.9 - mv/ input reverse voltage bv r ta = 2 5 , i r =10ua 5.0 - - v input capacitance c in v f =0, f=1mhz - 60 - pf *7 leak current ( input-output ) i i-o ta = 2 5 , 45%rh v i-o =3kvdc, t=5s - - 1.0 ua *7 isolation resistance ( input-output ) r i-o v i-o =500vdc - 10 12 - *7 capacitance ( input-output ) c i-o f=1mhz - 0.6 - pf *6 current transfer ratio is the ratio of inpu t current and output current expressed in %. *7 measured as 2-pin element ( short 1, 2, 3, 4 and 5, 6, 7, 8 )
product specification date 03/26/2012 no.62p51004 cosmo electronics corporation photocoupler KPC6N139H sheet 4 of 5 rev. 2 z switching characteristics ( ta=25 , v cc =5v ) parameter symbol conditions min. typ. max. unit r l =4.7k ? , i f =0.5ma - 5 25 us *8 propagation delay time output (1) ? (0) t phl r l =270 ? , i f =12ma - 0.3 1 us r l =4.7k ? , i f =0.5ma - 10 60 us *8 propagation delay time output (0) ? (1) t plh r l =270 ? , i f =12ma - 1.5 7 us *9 *10 instantaneous common mode rejection voltage ? output (1) ? cm h i f =0, v cm =10v p-p , r l =2.2k - 500 - v/us *9 *10 instantaneous common mode rejection voltage ? output (0) ? cm l i f =1.6ma, v cm =10v p-p , r l =2.2k - -500 - v/us *9 instantaneous common mode rejection voltage ? output (1) ? represents a common mode voltage variation that can hold the output above (1) level ( vo > 2.0v ) *10 instantaneous common mode rejection voltage ? output (0) ? represents a common mode voltage variation that can hold the output above (0) level ( vo < 0.8v ) *8 test circuit propagation delay time 8 7 6 5 i 100 i monitor f = 1/10 duty ratio pulse input 4 3 2 f 1 c =15pf l r l vo vcc t phl vo 1.5v 0 f i t plh 1.5v 5v *10 test circuit for instantaneous common mode rejection voltage 5 6 7 8 4 ff v b + v cm - i a 2 3 f 1 r l vo vcc=5v f i =16ma cm vo l 0.8v v ol i =0 f 0v cm vo h cm v 10v tr 10% 90% 10% tf 2v 5v 90%
product specification date 03/26/2012 no.62p51004 cosmo electronics corporation photocoupler KPC6N139H sheet 5 of 5 rev. 2 z notice the information contained in this document is intended to be a general product description and is subject to change without notice. please contact cosmo in order to obta in the latest device data sheets before using any cosmo device. cosmo does not assume any responsibility for use of any circui try described. no circuit patent licenses are implied. this publicatio n is the property of cosmo. no part of this publication may be rep roduced or copied in any form or by any means, or transferred to any th ird party without the prior written consent of cosmo electronics corporation. the devices listed in this document are designed for general applications only in electronic e quipment. no devices shall be deployed which require higher le vel of reliability such as ? medical and other life support equipments. ? space application. ? telecommunication equipment ( trunk lines ). ? nuclear power control equipment. unless it received prior writ ten approval from cosmo. cosmo takes no responsibility for damages arise form the improper usage of our device. pl ease contact cosmo for further information regarding the above notices.
|
